GSM Click
1 × R1,150.00 
WiFi Plus Click
1 × R2,350.00 
4-20 mA R Click
1 × R730.00 
Alcohol 3 Click
1 × R750.00 Subtotal: R4,980.00
R4,300.00 ex. VAT
Stock: Lead-time applicable.
| 5+ | R4,085.00 |
| 10+ | R3,977.50 |
| 15+ | R3,870.00 |
| 20+ | R3,762.50 |
Fast FT900 microcontroller with 256KB of Flash, 256KB of shadow RAM, operating at 100 MHz. Execution from shadow RAM gives it 3.1 DMIPS/MHz.
See the big picture. A 4.3” touch screen driven by FT810 graphics controller from FTDI delivers crystal sharp image in 480x272px resolution.
Nordic’s nRF240L01+ transceiver with active chip antenna will make you forget about wires. Drive it with simple SPI commands. It that easy.
Board has it all: USB connector, temperature sensor, PIN photosensor, IR receiver, accelerometer, battery charger, MP3 codec, buzzer, etc.
Click on the desired thumbnail to view full image.
Front side features RGB LED which is useful for simple visual signalization.
Four mounting holes, one in each corner of the board, facilitate board integration.
PIN photosensor enables you to measure ambient light and respond by dimming or brightening up the screen backlight.
IR receiver diode enables you to remotely control your device.
High quality reset button with surrounding reset circuitry ensures stable reset operation.
480×272 Color TFT Display with Touch Panel can display vivid and clear color images or advanced graphic content.
Every unused microcontroller pin is available through connection pads. They can be used to connect your mikromedia board with additional shields or accessory boards.
Two LEDs (Link and Ackowledge) are provided for monitoring ethernet communication.
We have added power indicator LED, so you can be sure whether your board has stable power supply.
Whenever your board charges the battery, this LED will glow in red. When it’s fully charged it will change to green. Handy, isn’t it?
High-performance FT900 microcontoller with 256KB of Flash, 128KB of RAM operating at 100 MHz with 3.1 DMIPS/MHz.
Pads for connecting and programming the board with mikroProg for FT90x external programmer and debugger.
Slim-line micro speaker with 0.7W continuous and 1W maximum power handling, suitable for space-limited applications.
Quadrupole audio connector enable you to connect headphones with microphone to the audio codec chip and use it in your applications.
Two position ON/OFF switch is a handy feature. It’s conveniently located right on the edge of the board.
VS1053 MPEG audio decoder with SPI interface for fast reproduction of Ogg Vorbis / MP3 / AAC / WMA / FLAC / MIDI audio files.
Connector for the TFT display flat cable is located at the back of the board.
FT810 is an easy-to-use graphic controller with an Embedded Video Engine (EVE) from the same vendor that provides the main MCU.
Board features MCP23S17, a 16-bit I/O expander with SPI clock speeds up to 10 MHz which provides two additional GPIO PORTS.
Store up to 8 Mbit of data in M25P80 Serial Flash Memory with 25 MHz SPI Bus Interface. It suports over 100,000 Erase/Program Cycles per Sector and has over 20 Year Data Retention.
8Mhz crystal oscillator circuit that provides external clock is connected to microcontroller osc pins.
Board contains 32.768kHz Crystal oscillator (X1) which provides external clock for internal RTCC module.
Microcontroler supports Full Speed and USB 2.0 OTG, so this connector allows you to communicate with a PC or other USB devices using USB connection.
microSD Card slot allows you to store large ammounts of data externally on microSD card using fast SPI communication.
Active RF chip antenna for 2.4 GHz RF transceiver.
Nordic nRF24L01+ is a wireless ultra low power 2.4 GHz RF transceiver. It has a simple UART interface.
MCP73832 Battery Charger circuit enables you to charge your Li-Polymer battery directly from USB port.
Li-Polymer battery connector allows you easier connection with your battery. Autonomous power supply will give your mikromedia the wings it deserves.
You can easily provide necessary power supply using these power supply screw terminals.
On-board microcontroller is preprogrammed with fast USB HID bootloader, so it’s ready to work right out of the box. You don’t have to spend a dollar more on programmers. If you need a debugger use mikroProg for FT90x.
Mikromedia Plus for FT90x is fully supported by mikroC, mikroBasic, mikrobasic and mikroPascal compilers for FT90x. Compilers come with dozens of examples that demostrate every feature of the board.
Easily create fantastic colorful graphical user interfaces (GUI) for mikromedia in VisualTFT software. Even total beginners will be able to create amazing mikromedia applications.
Click on the desired thumbnail to view full image.
Popular graphics controller FT810 handles the TFT display. It has graphic control, audio control, touch control interface and many other cool features.
VS1053 MPEG audio decoder with SPI interface for fast reproduction of Ogg Vorbis / MP3 / AAC / WMA / FLAC / MIDI audio files, 3.5mm four pole audio jack allows you to directly connect your headset to mirkomedia and develop various audio applications.
microSD Card slot allows you to store large ammounts of data externally on microSD card using fast SDIO communication.
Mikromedia plus for STM32 is equipped with the Rufa 2.4GHz antenna, from antenova(r). It allows easy development of applications that use wireless communication.
Microcontroler supports Full Speed and USB 2.0 OTG, so this connector allows you to communicate with a PC or other USB devices using USB connection.
Li-Polymer battery connector allows you easier connection with your battery. Autonomous power supply will give your mikromedia the wings it deserves.
| Weight | 360 g |
|---|---|
| Brand | MikroElektronika |
