LED Flash click

LED Flash click functions as a high power LED flash, and carries the CAT3224 flash LED driver. The click is designed to run on a 5V power supply. It communicates with the target microcontroller over the following pins on the mikroBUS™ line: AN, RST, PWM, and INT.

CAT3224 features

The CAT3224 is a very high−current integrated flash LED driver which also supports the charging function for a dual−cell supercapacitor applications. Ideal for Li−ion battery−powered systems, it delivers up to 4A LED flash pulses, far beyond the peak current capability of the battery.

Dual−mode 1x/2x charge pump charges the stacked supercapacitor to a nominal voltage of 5.4 V, while an active balance control circuit ensures that both capacitor cell voltages remain matched.

The driver also features two matched current sources. External resistors provide the adjustment for the maximum flash mode current (up to 4 A) and the torch mode current (up to 400 mA). A built−in safety timer automatically terminates the flash pulse beyond a maximum duration of 300 ms.

The CAT3224 has a shutdown mode that is so low that ON Semiconductor can safely call it “zero” mode. In this mode, it typically uses only 1μA.

Information about the LED indicators

Additional information about the pins

Specifications

Pinout diagram

This table shows how the pinout on LED Flash click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
Charge Supercapacitor Enable	CH_ENA	1	AN	PWM	16	TOR	Torch Enable
Flash Enable	FLS	2	RST	INT	15	FLG	Flash Ready Flag output, Open drain (Active low)
	NC	3	CS	TX	14	NC
	NC	4	SCK	RX	13	NC
	NC	5	MISO	SCL	12	NC
	NC	6	MOSI	SDA	11	NC
Not conncted	NC	7	3.3V	5V	10	+5V	Power supply
Ground	GND	8	GND	GND	9	GND	Ground

Programming

Code examples for LED Flash click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The demo is realised as FSM (Finite State Machine). It has four states for contolling output signals (TORCH, FLASH, CHRG).

The demo starts in charge state which enables charge mode. It waits for FLAG signal (active low) from LED driver to switch to ready state. When in ready state, user can press specified button to drive LEDs in flash mode, burst current for short duration of time. After flash state is over (300 ms), it returns to charge state. User, aslo can press specified button to switch between torch or flash states. When in torch state, the program puts LED driver in torch mode, which allows the LEDs to run for extended time.

01 void main() 
02 {
03     MCU_Init();
04 
05     state = STATE_CHARGE;
06     next_state = STATE_CHARGE;
07 
08     while(1) 
09     {
10         switch(state) 
11         {
12             case STATE_CHARGE:
13                 Write_Mode_Text(1, CL_GRAY, 1, CL_BLACK, 1, CL_GRAY);
14                 TORCH = 0;
15                 FLASH = 0;
16                 CHRG  = 1;
17 
18                 if(!FLAG)
19                     next_state = STATE_READY;
20             
21                 if(Button_Pressed(&GPIO_PORT_64_66, 0, &buttonstate_up))
22                     next_state = STATE_TORCH;
23                 
24                 break;
25 
26             case STATE_READY:
27                 Write_Mode_Text(0, 0, 0, 0, 1, CL_BLACK);
28                 if(Button_Pressed(&GPIO_PORT_64_66, 1, &buttonstate_center))
29                     next_state = STATE_FLASH;
30 
31                 if(Button_Pressed(&GPIO_PORT_64_66, 0, &buttonstate_up))
32                     next_state = STATE_TORCH;
33                 
34                 break;
35 
36             case STATE_FLASH:
37                 Write_Mode_Text(0, 0, 0, 0, 1, CL_GRAY);
38                 CHRG = 0;
39 
40                 FLASH = 1;
41                 Delay_ms(300);
42                 FLASH = 0;
43 
44                 next_state = STATE_CHARGE;
45                 break;
46 
47             case STATE_TORCH:
48                 Write_Mode_Text(1, CL_BLACK, 1, CL_GRAY, 1, CL_GRAY);
49                 TORCH = 1;
50                 FLASH = 0;
51                 CHRG  = 0;
52 
53                 if(Button_Pressed(&GPIO_PORT_64_66, 0, &buttonstate_up))
54                     next_state = STATE_CHARGE;
55                 
56                 break;
57         }
58         
59         state = next_state;
60         Delay_ms(POLLING_PERIOD);
61     }
62 }