Temp&Hum 17 Click

How does it work?

Temp&Hum 17 Click as its foundation uses the HS3001, a highly accurate, fully calibrated relative humidity and temperature sensor from Renesas. The humidity can be measured within a range of 0 to 100 %RH, while the temperature sensor is designed for a range of -10 to 80 °C. The typical accuracy for humidity is ±1.5 %RH in the measuring range of 10 up to 90 %RH at ambient temperature, and ±0.2 °C for temperature between -10 – +80 °C with very low power consumption.

The HS3001 digital sensor accurately measures relative humidity and temperature levels. The measured data is internally corrected and compensated for accurate operation over a wide range of temperature and humidity levels, which brings us to its highlighted feature – user calibration is not required. The entire output consists of only four bytes of data; that’s why calculating the corresponding relative humidity in percent and temperature in degrees Celsius is very easy.

Temp&Hum 17 Click communicates with MCU using the standard I2C 2-Wire interface to read data and configure settings, supporting Standard Mode operation with a clock frequency up to 100kHz and Fast Mode up to 400kHz. The HS3001 is also factory-programmed to operate even in Sleep Mode. In Sleep Mode, the sensor waits for commands from the MCU before taking measurements and only performs conversions when it receives a Measurement Request command; otherwise, it is always powered down.

This Click board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to use the I2C communication lines properly. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.

Specifications

Pinout diagram

This table shows how the pinout on Temp&Hum 17 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
	NC	1	AN	PWM	16	NC
	NC	2	RST	INT	15	NC
	NC	3	CS	RX	14	NC
	NC	4	SCK	TX	13	NC
	NC	5	MISO	SCL	12	SCL	I2C Clock
	NC	6	MOSI	SDA	11	SDA	I2C Data
Power Supply	3.3V	7	3.3V	5V	10	5V	Power Supply
Ground	GND	8	GND	GND	9	GND	Ground

Onboard settings and indicators

Temp&Hum 17 Click electrical specifications

Software Support

We provide a library for the Temp&Hum 17 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for Temp&Hum 17 Click driver.

Key functions:

• temphum17_cfg_setup – Config Object Initialization function.
• temphum17_init – Initialization function.
• temphum17_default_cfg – Click Default Configuration function.

Examples description

This library contains API for the Temp&Hum 17 Click driver. This demo application shows an example of relative humidity and temperature measurement.

The demo application is composed of two sections :

void application_task ( void ) {
    if ( temphum17_get_temp_hum( &temphum17, TEMPHUM17_RESOLUTION_14_BITS, &temperature, &humidity ) == TEMPHUM17_STATUS_VALID_DATA ) {
        log_printf( &logger, "  Temperature : %.02f Crn  Humidity    : %.02f %%rn", temperature, humidity, status );
    } else {
        log_printf( &logger, "     Measurement ErrorrntStale Datarn" );    
    }
    
    log_printf( &logger, "-------------------------rn", temperature, humidity, status );
    Delay_ms( 1000 );  
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.TempHum17

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

mikroSDK

This Click board™ is supported with mikroSDK – MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

For more information about mikroSDK, visit the official page.