Multi Stepper Click – TB62261

How does it work?

Multi Stepper Click as its foundation uses the TB62261FTG, a two-phase bipolar stepping motor driver using a PWM chopper (customized by external resistance R2 and capacitor C1) from Toshiba Semiconductor. The TB62261FTG incorporates a low on-resistance MOSFET output stage, which can deliver a 1.2A current with a motor output voltage rating of 38V, in addition to integrated protection mechanisms such as over-current and over-temperature detection. In addition, it supports full-, half-, and quarter-step resolution, with the help of which motor noise can be significantly reduced with smoother operation and more precise control.

As mentioned in the product description, this stepping motor driver is PHASE-in controlled. These control signals are provided through the PCA9555A port expander, which establishes communication with the MCU via the I2C serial interface. This Click board™ also allows a connection of external control signals on the onboard header J1 on pins labeled as P1 and P2 for the device’s PHASE-in control. The PCA9555A also allows choosing the least significant bit (LSB) of its I2C slave address by positioning SMD jumpers labeled as ADDR SEL to an appropriate position marked as 0 and 1.

In addition to PHASE signals, four A/B channel logic signals, INA1, INB1, INB2, and INA2, are used to control the motor, adjusting the desired step resolution. The first three signals are controlled by AN, CLK, and EN pins of the mikroBUS™ socket. The INA2 signal provides the possibility of dual control selected by positioning SMD jumper labeled as JP5 to an appropriate position marked as P6 or INT, which choose control via expander or INT pin of the mikroBUS™ socket. In the case of the selected INT position of the JP5 jumper, the JP10 jumper needs to be unpopulated.

Also, this Click board™ has a Standby function routed to the RST pin of the mikroBUS™ socket used to switch to Standby mode by setting all motor control pins to a low logic state. When the Standby mode is active, the TB62261FTG stops supplying the power to the internal oscillating circuit and motor output part (the motor drive cannot be performed). This Click board™ also has an additional LED for anomaly indication, but since this version of the stepper driver does not support this feature, this indicator cannot be used.

The motor A/B channel current output value can be set manually using an onboard trimmer labeled as VR1, which sets the reference voltage from 0V to 3.3V. The default configuration of the JP4 jumper is the VREF position that sets both channels’ output current via the VR1 trimmer. In this case, avoid position P4 on a jumper JP4 since the VREFA pin requires an analog signal for setting.

Multi Stepper Click supports an external power supply for the TB62261FTG, which can be connected to the input terminal labeled as VM and should be within the range of 10V to 38V, while the stepper motor coils can be connected to the terminals labeled as B+, B-, A-, and A+.

This Click board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to use communication lines properly. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.

Specifications

Pinout diagram

This table shows how the pinout on Multi Stepper Click – TB62261 corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
A-Channel Control 1	AN	1	AN	PWM	16	CLK	B-Channel Control 1
Standby Control	RST	2	RST	INT	15	INT	Interrupt / A-Channel Control 2
B-Channel Control 2	EN	3	CS	RX	14	NC
	NC	4	SCK	TX	13	NC
	NC	5	MISO	SCL	12	SCL	I2C Clock
	NC	6	MOSI	SDA	11	SDA	I2C Data
Power Supply	3.3V	7	3.3V	5V	10	5V	Power Supply
Ground	GND	8	GND	GND	9	GND	Ground

Onboard settings and indicators

Multi Stepper Click – TB62261 electrical specifications

Software Support

We provide a library for the Multi Stepper TB62261 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for Multi Stepper TB62261 Click driver.

Key functions

• multisteppertb62261_set_step_mode This function sets the step mode resolution settings in ctx->step_mode.

• multisteppertb62261_drive_motor This function drives the motor for the specific number of steps at the selected speed.

• multisteppertb62261_set_direction This function sets the motor direction to clockwise or counter-clockwise in ctx->direction.

Example Description

This example demonstrates the use of the Multi Stepper TB62261 Click board™ by driving the motor in both directions for a desired number of steps.

void application_task ( void ) 
 { 
     multisteppertb62261_set_direction ( &multisteppertb62261, MULTISTEPPERTB62261_DIR_CW ); 
     if ( MULTISTEPPERTB62261_OK == multisteppertb62261_drive_motor ( &multisteppertb62261, 200,  
                                                                      MULTISTEPPERTB62261_SPEED_FAST ) ) 
     { 
         log_printf ( &logger, " Move 200 steps clockwise rnn" ); 
         Delay_ms ( 2000 ); 
     } 

     multisteppertb62261_set_direction ( &multisteppertb62261, MULTISTEPPERTB62261_DIR_CCW ); 
     if ( MULTISTEPPERTB62261_OK == multisteppertb62261_drive_motor ( &multisteppertb62261, 100, 
                                                                      MULTISTEPPERTB62261_SPEED_FAST ) ) 
     { 
         log_printf ( &logger, " Move 100 steps counter-clockwise rnn" ); 
         Delay_ms ( 2000 ); 
     } 
 }

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.MultiStepperTB62261

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.

mikroSDK

This Click board™ is supported with mikroSDK – MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

For more information about mikroSDK, visit the official page.