LTE Cat.1 3 Click (for North America)

How does it work?

LTE Cat.1 3 Click (for North America) is based on the EG91NAXDGA-128-SGNS, a 4G wireless communication data-only module from Quectel with receive diversity. This module supports multiple wireless communication standards, including LTE-FDD and WCDMA, providing reliable data connectivity across various networks. With the ability to also provide voice functionality (the telematics version supporting voice and data functions), this module is designed to meet customers’ specific needs. The LTE Cat.1 3 Click supports multiple LTE bands (B2/B4/B5/B12/B13/B25/B26) and RX diversity for bands B2, B4, and B5. Additionally, it offers multi-constellation GNSS support for GPS, GLONASS, BeiDou/Compass, Galileo, and QZSS. It is fully integrated with Internet service protocols such as TCP, UDP, and PPP, making it easy to use with extended AT commands. This Click board™ meets almost all requirements for M2M applications such as automotive, smart metering, tracking systems, security, routers, wireless POS, and many more.

Communication between the EG91NAXDGA-128-SGNS and the host MCU is made through a UART interface, using standard UART RX and TX pins and hardware flow control pins (CTS/RTS/RI – Clear to Send/Ready to Send/Ring Indicator) for efficient data transfer. The module defaults to a communication speed of 115200bps, allowing for seamless data exchange over AT commands. Notably, this telematics version of the module also features an audio interface, which can be accessed via the I2C interface.

The LTE Cat.1 3 Click audio interface operates through the MAX9860, a 16-bit mono audio voice codec configurable via the I2C interface. This setup works with a jack on the back of the board designed for CTIA standard headphones, which are commonly used in modern smartphones and feature a combined audio and microphone connector. This standard ensures compatibility with a wide range of headphones and headsets. Additionally, the audio interface supports advanced features such as echo cancellation and noise suppression, enhancing the clarity and quality of voice communications.

The LTE Cat.1 3 Click also includes a USB Type C connector for both power and data transfer, compliant with the USB 2.0 specification (slave only). This interface supports data transfer rates of up to 480Mbps, facilitating AT command communication, data transmission, GNSS NMEA sentence output, software debugging, firmware upgrades, and voice over USB. The board features a USB FW upgrade switch labeled USB BOOT to manage firmware upgrades. This switch has positions 0 for normal operation and 1 for firmware upgrades over USB, ensuring a straightforward upgrade process.

In addition, this Click board™ includes several additional functionalities that enhance its usability and control. The PWR button allows users to easily power the module on or off, while the RESET button provides a quick way to reset the module. These functions can also be controlled digitally via the mikroBUS™ pins PWR and RST, offering greater flexibility. Moreover, these controls have dedicated test points for easier debugging and testing. The board also features two visual indicators to provide real-time status updates. The red NET LED offers feedback on network activity: it flickers slowly when searching for a network, flickers quickly during data transfer, and remains steadily on during voice calls. The yellow STAT LED indicates the module’s power status, which stays off when the module is off and turns on when the module is powered on. The board also includes DBG TX/RX interface test points for debug UART communication, simplifying the development and troubleshooting process.

The board features three u.Fl connectors for GNSS, LTE, and LTE/WCDMA receive the diversity antenna that MIKROE offers, the LTE Flat Rotation Antenna and Active GPS Antenna combined with an IPEX-SMA cable for flexible and efficient connectivity options. In addition, the user can easily choose the power supply of the GNSS antenna by choosing between 3.3V and 5V on the GNSS ANT jumper. Additionally, the board is equipped with a micro SIM card holder that supports both 1.8V and 3.0V uSIM cards, ensuring compatibility with a wide range of cellular networks and allowing users to select the most appropriate service provider for their particular use case.

This Click board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. Since the EG91NAXDGA-128-SGNS operates at 3.8V, logic-level translators, the TXB0106 and PCA9306, are also used for proper operation and an accurate signal-level translation. This way, both 3.3V and 5V capable MCUs can use the communication lines properly. Also, this Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used as a reference for further development.

Specifications

Pinout diagram

This table shows how the pinout on LTE Cat.1 3 Click (for North America) corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
Module Power-ON	PWR	1	AN	PWM	16	RI	Ring Indicator
Reset / ID SEL	RST	2	RST	INT	15	CTS	UART CTS
UART RTS / ID COMM	RTS	3	CS	RX	14	TX	UART TX
	NC	4	SCK	TX	13	RX	UART RX
	NC	5	MISO	SCL	12	SCL	I2C Clock
	NC	6	MOSI	SDA	11	SDA	I2C Data
Power Supply	3.3V	7	3.3V	5V	10	5V	Power Supply
Ground	GND	8	GND	GND	9	GND	Ground

Onboard settings and indicators

LTE Cat.1 3 Click electrical specifications

Software Support

We provide a library for the LTE Cat.1 3 NAX Click as well as a demo application (example), developed using MIKROE compilers. The demo can run on all the main MIKROE development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager (recommended), downloaded from our LibStock™ or found on MIKROE github account.

Library Description

This library contains API for LTE Cat.1 3 NAX Click driver.

Key functions

• ltecat13nax_write_register This function writes a data byte into the selected register address.

• ltecat13nax_max9860_cfg This function is used to set basic config for MAX9860 of LTE Cat.1 3 NAX click board.

• ltecat13nax_send_sms_pdu This function sends text message to a phone number in PDU mode.

Example Description

Application example shows device capability of connecting to the network and sending SMS, TCP/UDP messages, calling the selected number, or getting GNSS location using standard “AT” commands.

void application_task ( void )  
 { 
     switch ( example_state ) 
     { 
         case LTECAT13NAX_CONFIGURE_FOR_NETWORK: 
         { 
             if ( LTECAT13NAX_OK == ltecat13nax_cfg_for_network( ) ) 
             { 
                 example_state = LTECAT13NAX_WAIT_FOR_CONNECTION; 
             } 
             break; 
         } 
         case LTECAT13NAX_WAIT_FOR_CONNECTION: 
         { 
             if ( LTECAT13NAX_OK == ltecat13nax_check_connection( ) ) 
             { 
                 example_state = LTECAT13NAX_CONFIGURE_FOR_EXAMPLE; 
             } 
             break; 
         } 
         case LTECAT13NAX_CONFIGURE_FOR_EXAMPLE: 
         { 
             if ( LTECAT13NAX_OK == ltecat13nax_cfg_for_example( ) ) 
             { 
                 example_state = LTECAT13NAX_EXAMPLE; 
             } 
             break; 
         } 
         case LTECAT13NAX_EXAMPLE: 
         { 
             ltecat13nax_example( ); 
             break; 
         } 
         default: 
         { 
             log_error( &logger, " Example state." ); 
             break; 
         } 
     } 
 }

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager (recommended), downloaded from our LibStock™ or found on MIKROE github account.

Other MIKROE Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.LTECat13NAX

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MIKROE compilers.

mikroSDK

This Click board™ is supported with mikroSDK – MIKROE Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

For more information about mikroSDK, visit the official page.