Expand 3 Click

How does it work?

Expand 3 Click is based on the DS2408, an 8-channel programmable I/O expander from Analog Devices. The DS2408 comes with a factory-lasered 64-bit registration number that allows multiple same Click boards™ to be connected on the same data line. It communicates with the host MCU through a standard Dallas Semiconductor 1-Wire interface (15.3kbps or 100kbps), with PIO outputs configured as open-drain providing a maximum on-resistance of 100Ω. A robust PIO channel-access communication protocol ensures that PIO output-setting changes occur error-free making it suitable to latch PIO logic states into external circuitry such as a D/A converter (DAC) or microcontroller data bus.

This Click board™ communicates with MCU using the 1-Wire interface that, by definition, requires only one data line (and ground) for communication with MCU. In the absence of main power supply, data line can also power the sensor parasitically. The 1-Wire communication line is routed to the GP SEL jumper allowing the 1-Wire communication signal to the PWM pin or the AN pin of the mikroBUS™ socket. These pins are labeled OW0 and OW1, respectively, the same as the SMD jumper positions, making selecting the desired pin straightforward. Besides, the user is provided with the possibility of external use of the data line (OW) through the unpopulated header in the manner and needs that best suit the desired application, alongside a reset feature.

Each DS2408 has its own unalterable and unique 64-bit ROM registration number that is, as mentioned, factory-lasered into the chip. The registration number guarantees unique identification and addresses the device in a multidrop 1-Wire net environment. Multiple DS2408 devices can reside on a common 1-Wire bus and can operate independently of each other. The DS2408 also supports 1-Wire conditional search capability based on programmable PIO conditions or Power-on-Reset activity.

This Click board™ can operate with both 3.3V and 5V logic voltage levels selected via the PWR SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to use the communication lines properly. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.

Specifications

Pinout diagram

This table shows how the pinout on Expand 3 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
1-Wire Data IN/OUT	OW1	1	AN	PWM	16	OW0	1-Wire Data IN/OUT
Reset	RST	2	RST	INT	15	NC
	NC	3	CS	RX	14	NC
	NC	4	SCK	TX	13	NC
	NC	5	MISO	SCL	12	NC
	NC	6	MOSI	SDA	11	NC
Power Supply	3.3V	7	3.3V	5V	10	5V	Power Supply
Ground	GND	8	GND	GND	9	GND	Ground

Onboard settings and indicators

Expand 3 Click electrical specifications

Software Support

We provide a library for the Expand 3 Click as well as a demo application (example), developed using Mikroe compilers. The demo can run on all the main Mikroe development boards.

The package can be downloaded/installed directly from NECTO Studio Package Manager(recommended), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

The library covers all the necessary functions to control Expand 3 Click board. Expand 3 click communicates with the target board via 1-Wire protocol. This library contains drivers for write and read data from DS2408 sensor, set and get configuration of DS2408 sensor.

Key functions

• uint8_t expand3_getConfiguration() Get configuration function.

• void expand3_setConfiguration( uint8_t cfg ) Set configuration function

• uint8_t expand3_setState( uint8_t state ) Set state function

Example Description

void applicationTask()
{
    configData = expand3_getConfiguration();

    if ( configData == _EXPAND3_CONFIG_SUCCESS )
    {
        mikrobus_logWrite( "   Writing success   ", _LOG_LINE );
        mikrobus_logWrite( "---------------------", _LOG_LINE );

        expand3_setState( 0xFF );

        mikrobus_logWrite( "   State = 11111111  ", _LOG_LINE );
        Delay_1sec();
        Delay_1sec();

        expand3_setState( 0x55 );

        mikrobus_logWrite( "   State = 01010101  ", _LOG_LINE );
        Delay_1sec();
        Delay_1sec();

        expand3_setState( 0xCB );

        mikrobus_logWrite( "   State = 11001011  ", _LOG_LINE );
    }
    else
    {
        mikrobus_logWrite( "    Writing Error    ", _LOG_LINE );
    }
    
    mikrobus_logWrite( "---------------------", _LOG_LINE );
    Delay_1sec();
    Delay_1sec();
}

The full application code, and ready to use projects can be found on our LibStock page.

Other Mikroe Libraries used in the example:

• One_Wire
• UART

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.

mikroSDK

This Click board™ is supported with mikroSDK – MikroElektronika’s Software Development Kit. mikroSDK should be downloaded from the LibStock™ and installed for the compiler you are using to ensure proper operation of mikroSDK compliant Click board™ demo application.

For more information about mikroSDK, visit the official page.