RTC Click
2 × R445.00 
Ribbon Cable 40-wire, Female/Female, 20 cm
1 × R110.00 
GSM/GPRS Straight Rubber Antenna
1 × R145.00 
METHANE Click
1 × R385.00 Subtotal: R1,530.00
R3,000.00 ex. VAT
Stock: Lead-time applicable.
| 5+ | R2,850.00 |
| 10+ | R2,700.00 |
| 15+ | R2,550.00 |
| 20+ | R2,454.00 |
High quality reset button with surrounding reset circuitry ensures stable reset operation.
EasyPIC v7 is the only board in the world to provide two mikroBUS sockets for mikroElektronika Click Boards. mikroBUS provides simple and effective Plug-and-Play connectivity solution.
EasyPIC v7 is the only board in the world to provide two mikroBUS sockets for mikroElektronika Click Boards. mikroBUS provides simple and effective Plug-and-Play connectivity solution.
Board provides USB-B connector necessary for writting applications that use USB communication. Connector can be routed to either PORTC or PORTA, depending on the target microcontroller.
If you need to use other external programmer with EasyPIC v7, we have provided the ICD2/ICD3 compatible connector, so you can override the on-board mikroProg.
On-board mikroProg In-Circuit Debugger and programmer is supports over 387 microcontrollers from Microchip.
Programmer USB connector is connected to on-board mikroProg, but can also be used to power the board, when the J6 jumper in the Power Supply section is in the USB position.
Board is equipped with power supply unit capable of supporting both 3.3V and 5V microcontrollers. Board can be powered over USB cable, or external adapter connectors.
FTDI chip allows your EasyPIC v7 board to be connected with a PC through USB cable over UART connection.
You can implement UART communication through RS-232 connector provided on the board.
Driving 7-segment displays is fun! EasyPIC v7 provides 4-digit display for your applications.
Board is equipped with LCD 2×16 connector which allows you to connect LCD 2×16 display and place it securely using plastic distancer, specially designed for this purpose.
You can place GLCD 128×64 display directly on the board and firm it in place securely using high-quality plastic distancer, specially designed for this purpose.
We have provided additional PORT header on the left side of the board, so you can now access the desired microcontroller pins on the other side of the board too.
Touch panel controller with connector is provided for analog resistive touch panels attached to the GLCD 128×64 to form GLCD Touch screen.
GLCD and LCD backlight can be driven with PWM signal from the microcontroller, or they can be turned on in full brightness.
You can store 8×256 bytes of configuration data or other data into on-board 24AA01 Serial EEPROM with I2C interface.
You can simulate analog inputs using two provided analog potentiometers which can be connected to each of the 10 supported microcontroller analog input pins.
This potentiometer allows you to adjust the contrast level of the pixels on your GLCD 128×64 display.
This potentiometer allows you to adjust the contrast level of the pixels on your LCD 2×16 character display.
With piezo buzzer you can debug your applications, or have audio signalization feature. It can be connected to two digital output pins, one of which is the output of PWM module.
Board supports Dallas DS1820 One-Wire digital temperature sensor. You can measure temperatures from -55C to +125C (-67F to +257F), with 0.5C accuracy.
The LM35 is a low-cost precision integrated-circuit analog temperature sensor. It can measure temeperatures from -55C to +150C with 0.25C accuracy at room temperatures.
With just enough RAM and Flash, PIC18F45K22 microcontroller will provide you with enough power for most of your projects.
8Mhz oscillator circuit that provides external clock is connected to microcontroller osc pins.
Three separate GND pins are available on the board for easier connection of GND reference for oscilloscope probes.
We have also provided 1×10 soldering pads for further connectivity in each Input/Output group.
Push buttons in each Input/Output group enable you to have digital inputs on each port pin. Buttons are of high quality and have an exceptional and stable response.
Two male IDC10 port headers are available in each Input/Output group, which is convenient for easier access to any PORT pin.
Tri-state DIP switches are used to enable 4K7 pull-up or pull-down resistor on ony desired PORT pin.
Each Input/Output PORT group contains red SMD LEDs with low current consumption of only 1mA. Board contains total of 36 LEDs for PORT pins.
EasyPIC v7 is the seventh generation of our famous PIC development board. It is the product of accumulated knowledge over the past 10 years, and it’s state of the art of design, functionality and quality. It is loved by beginners and hobbyists, as well as professionals, and used in education and development by thousands. Board comes with PIC18F45K22 device.
ICD2 connector enables users to work with other programmers.
Write UART applications for laptops too. Besides RS-232, we also added USB-UART.
GLCD 128×64 and LCD 2×16 character displays are now closer together.
It’s back! 4 digit 7 segment display is now a part of EasyPIC v7.
Another row of PORT headers available on the left side. Connectivity at its best.
We added three additional GND pins for easier access of your oscilloscope probes.
With two mikroBUS™ sockets you can add dozens of new functionality to your board with minimum hardware adjustments. Collection of mikroBUS™ compatible Click Boards is growing rapidly, and we have designed them with great care, so you don’t have to make any complicated settings. Just plug your board in, and you are good to go.
| Weight | 1240 g |
|---|---|
| Brand | MikroElektronika |
