tRF Click
1 × R1,050.00 
Alcohol Click
1 × R335.00 
Alcohol 3 Click
1 × R710.00 
RFid Click
1 × R650.00 
M-BUS RF 4 Click
1 × R1,050.00 Subtotal: R3,795.00
R6,100.00 ex. VAT
Stock: Lead-time applicable.
| 5+ | R5,795.00 |
| 10+ | R5,642.50 |
| 15+ | R5,490.00 |
| 20+ | R5,337.50 |
High quality reset button with surrounding reset circuitry ensures stable reset operation.
EasyMx PRO™ v7 for Tiva™ C Series provides two mikroBUS™ sockets for MikroElektronika click™ Boards. mikroBUS™ provides simple and effective Plug-and-Play connectivity solution.
EasyMx PRO™ v7 for Tiva™ C Series provides two mikroBUS™ sockets for MikroElektronika click™ Boards. mikroBUS™ provides simple and effective Plug-and-Play connectivity solution.
Audio connectors enable you to connect headphones and microphone with the audio codec chip and use it in your applications.
VS1053 MPEG audio codec with SPI interface is available for audio input and output. Codec supports many compression file formats.
You can store 8×256 bytes of configuration data or other data into on-board 24AA01 Serial EEPROM with I2C interface.
Store up to 8 Mbit of data in M25P80 Serial Flash Memory with 25 MHz SPI Bus Interface. It suports over 100,000 Erase/Program Cycles per Sector and has over 20 Years of Data Retention.
Microcontrollers with internal ethernet support can be connected to this RJ-45 connector to establish ethernet communication.
On-board mikroProg™ In-Circuit Debugger and programmer supports over 55 Tiva™ C Series ARM® Cortex™-M4 MCUs from Texas Instruments®.
Programmer USB connector is connected to on-board mikroProg™, but can also be used to power the board, when the J1 jumper in the Power Supply section is in the USB position.
Board is equipped with a power supply unit capable of supporting 3.3V microcontrollers and peripherals. Board can be powered over USB cable, or external adapter connectors.
Board supports Dallas DS1820 One-Wire digital temperature sensor. You can measure temperatures from -55C to +125C (-67F to +257F), with 0.5C accuracy.
The LM35 is a low-cost precision integrated-circuit analog temperature sensor. It can measure temeperatures from -55C to +150C with 0.25C accuracy at room temperatures.
Fast on-board FTDI chip with USB connector, allows you to communicate with a PC or other UART devices using USB-UART connection.
Fast on-board FTDI chip with USB connector, allows you to communicate with a PC or other UART devices using USB-UART connection.
USB Host Connector enables your device to behave as USB host. You can communicate with other USB slave devices, such as Flash Sticks, cameras, mp3 players and more.
USB Device Connector is used for connecting the board with other devices such as a PC using fast USB 2.0 communication.
This potentiometer allows you to adjust the contrast level of the pixels on your GLCD 128×64 display.
The Cortex Debug Connector supports JTAG debug, Serial Wire debug and Serial Wire Viewer operations (via SWO connection when Serial Wire debug mode is used).
Board contains MCP2551 a CAN controller chip connected to a screw terminal connector. This way you can implement industry-standard CAN communication with your device.
With piezo buzzer you can debug your applications, or have audio signalization feature. It can be connected to two digital output pins, one of which is the output of PWM module.
Tri-state DIP switches are used to enable 4K7 pull-up or pull-down resistor on ony desired PORT pin.
Push buttons in each Input/Output group enable you to have digital inputs on each port pin. Buttons are of high quality and have an exceptional and stable response.
320×240 TFT Color Display with Touch Panel can display vivid and clear color images or advanced graphic content.
Each Input/Output PORT group contains red SMD LEDs with low current consumption of only 1mA. Board contains total of 36 LEDs for PORT pins.
Two male IDC10 port headers are available in each Input/Output group, which is convenient for easier access to any PORT pin.
Navigation switch can be used for handling the on-screen menus or as a generic input device.
Use these switches to pull-up or pull-down buttons in each input/output group.
ARM® Cortex™-M4 with 120MHz operation; 0-wait states execution from 1024Kbytes of Flash memory, 256kbytes of RAM, low power, rich peripherals, you name it!
Three separate GND pins are available on the board for easier connection of GND reference for oscilloscope probes.
Two male IDC10 port headers are available in each Input/Output group, which is convenient for easier access to any PORT pin.
microSD Card slot allows you to store large ammounts of data externally on microSD card using fast SPI communication.
You can simulate analog inputs using two provided analog potentiometers which can be connected to each of the 10 supported microcontroller analog input pins.
EasyMx PRO™ v7 for Tiva™ C Series is a full-featured development board for TI’s Tiva™ C Series ARM® Cortex™-M4 microcontrollers. It contains many on-board modules necessary for developing a variety of applications, including multimedia, Ethernet, USB, CAN and other. On-board mikroProg™ programmer and debugger supports over 55 TI Tiva™ C Series microcontrollers. Board is delivered with MCU socket containing TM4C129XNCZAD.
Ethernet connector (RJ-45) allows you to develop ethernet applications.
Port headers are grouped toghether with their buttons and LEDs
EasyTFT board with touch screen enables you to develop multimedia applications.
Piezo Buzzer allows you to implement audio signalization feature in your prototype.
Write UART applications for laptops too. We provided two USB-UART modules.
Board contains microSD card slot for storing large amount of data on external media.
Audio in and out jacks are connected to on-board mp3 codec chip.
Serial Flash and Serial EEPROM are available as additional storage.
| Weight | 1240 g |
|---|---|
| Brand | MikroElektronika |
