Diff Press 3 Click

How does it work?

Diff Press 3 Click is based on the WSEN-PDUS ( 2513130810401 ), a differential pressure sensor from Würth Elektronik. The sensor has high accuracy, can measure different transfer pressure ranges from -100kPa up to 1000kPa and has a response time of 2.2ms. There are two pots that except ∅2.2 hoses, where one of them is a high-pressure side, while the other is designated as the vacuum side. The hoses are not included with the Diff Press 3 Click. As for temperature, this sensor can measure temperatures in a range of 0 up to 70°C and in ADC resolution of 15 bits.

Diff Press 3 Click can use a standard 2-Wire I2C interface to communicate with the host MCU, where you can read both the pressure and the temperature measurements. In addition to the I2C interface, the output of the pressure output of the sensor can be read over the analog AN pin of the mikroBUS™ socket, where you can read only pressure measurements.

As the 2513130810401 WSEN-PDUS sensor works on 5V, this Click board™ comes equipped with the PCA9306, a dual bidirectional I2C bus and SMBus voltage-level translator from Texas Instruments, which allows the use of this Click board™ with systems with 3.3V logic level. AN SEL jumper allows you to use a 5V or 2.5V logic level over a voltage divider, where 2.5V is set by default.

This Click board™ can operate with either 3.3V or 5V logic voltage levels selected via the VCC SEL jumper. This way, both 3.3V and 5V capable MCUs can use the communication lines properly. Also, this Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.

Specifications

Pinout diagram

This table shows how the pinout on Diff Press 3 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
Analog Output	AN	1	AN	PWM	16	NC
	NC	2	RST	INT	15	NC
ID COMM	CS	3	CS	RX	14	NC
	NC	4	SCK	TX	13	NC
	NC	5	MISO	SCL	12	SCL	I2C Clock
	NC	6	MOSI	SDA	11	SDA	I2C Data
Power Supply	3.3V	7	3.3V	5V	10	5V	Power Supply
Ground	GND	8	GND	GND	9	GND	Ground

Onboard settings and indicators

Diff Press 3 Click electrical specifications

Software Support

We provide a library for the Diff Press 3 Click as well as a demo application (example), developed using MIKROE compilers. The demo can run on all the main MIKROE development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager (recommended), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for Diff Press 3 Click driver.

Key functions

• diffpress3_get_pressure Diff Press 3 get pressure function.

• diffpress3_get_temperature Diff Press 3 get temperature function.

• diffpress3_read_raw_adc Diff Press 3 read raw ADC value function.

Example Description

This library contains API for the Diff Press 3 Click driver. This demo application shows an example of differential pressure and temperature measurement.

void application_task ( void )  
 { 
     float pressure, temperature; 
     if ( DIFFPRESS3_OK == diffpress3_get_pressure( &diffpress3, &pressure ) ) 
     { 
         log_printf( &logger, " Diff Pressure: %.3f [kPa]rn", pressure ); 
         Delay_ms( 100 ); 
     } 
     if ( DIFFPRESS3_OK == diffpress3_get_temperature( &diffpress3, &temperature ) ) 
     { 
         log_printf( &logger, " Temperature: %.2f [C]rn", temperature ); 
         Delay_ms( 100 ); 
     } 
     log_printf( &logger, "---------------------rn" ); 
     Delay_ms( 1000 ); 
 }

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager (recommended), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.DiffPress3

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MIKROE compilers.

mikroSDK

This Click board™ is supported with mikroSDK – MIKROE Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

For more information about mikroSDK, visit the official page.