AudioAmp 8 Click

How does it work?

AudioAmp 8 Click as its foundation uses the MA12070, a super-efficient audio power amplifier based on proprietary multi-level switching technology that enables low power loss during operation from Infineon Technologies. The MA12070 is equipped with an intelligent power management algorithm that applies automatic power mode selection during audio playback. In this state, the amplifier will seamlessly transition between three different power modes depending on the audio level to achieve optimal power loss, audio performance, and EMI. Alternatively, it is also possible to manually select the desired power mode for the MA12070 via a serial interface.

The MA12070 communicates with MCU using the standard I2C 2-Wire interface that supports Standard (100 kHz) and Fast (400 kHz) modes of operation. It has a 7-bit slave address with the first five MSBs fixed to 01000. The address pins are programmed by the user and determine the value of the last two LSBs of the slave address, which can be selected by positioning onboard SMD jumpers labeled as ADDR SEL to an appropriate position marked as 0 or 1.

This Click board™ supports an external power supply for the motor, which can be connected to the input terminal labeled as VIN and should be within the range of 6V to 26V, while the input audio can be brought to the input jack labeled as AUDIO IN and after specific processing reproduced on the speakers of the desired channel SPK OUT.

The MA12070 is highly flexible regarding the configuration of the four power amplifier channels. It can be set to four different output configurations by setting the configuration pins MS0 and MS1, routed to the INT and PWM pins of the mikroBUS™ socket. In addition to these pins, this Click board™ uses a few more pins of the mikroBUS™ socket. The Enable pin, labeled as EN and routed to the CS pin of the mikroBUS™ socket, optimizes power consumption used for power ON/OFF purposes, while the MUT pin routed to the RST pin allows users to mute audio on connected speakers.

Besides, it is possible to detect operational irregularities, such as overcurrent and short-circuit detection. An indication of such a condition is performed using the red LED indicator labeled as ERROR, alongside an audio clipping indication accomplished using the blue LED indicator labeled as CLIP which indicates when audio output is close to clipping.

This Click board™ can be operated only with a 5V logic voltage level. The board must perform appropriate logic voltage level conversion before using MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development.

Specifications

Pinout diagram

This table shows how the pinout on AudioAmp 8 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
	NC	1	AN	PWM	16	MS0	Output Stage Config. 0
Audio Mute	MUT	2	RST	INT	15	MS1	Output Stage Config. 1
Device Enable	EN	3	CS	RX	14	NC
	NC	4	SCK	TX	13	NC
	NC	5	MISO	SCL	12	SCL	I2C Clock
	NC	6	MOSI	SDA	11	SDA	I2C Data
	NC	7	3.3V	5V	10	5V	Power Supply
Ground	GND	8	GND	GND	9	GND	Ground

Onboard settings and indicators

AudioAmp 8 Click electrical specifications

Software Support

We provide a library for the Audio Amp 8 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Library Description

This library contains API for Audio Amp 8 Click driver.

Key functions:

• audioamp8_cfg_setup – Config Object Initialization function.
• audioamp8_init – Initialization function.
• audioamp8_default_cfg – Click Default Configuration function.

Examples description

This library contains API for AudioAmp 8 Click driver. The library initializes and defines the I2C bus drivers to write and read data from registers.

void application_init ( void ) 
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    audioamp8_cfg_t audioamp8_cfg;  /**< Click config object. */

    // Logger initialization.
    LOG_MAP_USB_UART( log_cfg );
    log_cfg.level = LOG_LEVEL_DEBUG;
    log_cfg.baud = 115200;
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    audioamp8_cfg_setup( &audioamp8_cfg );
    AUDIOAMP8_MAP_MIKROBUS( audioamp8_cfg, MIKROBUS_1 );
    err_t init_flag = audioamp8_init( &audioamp8, &audioamp8_cfg );
    if ( I2C_MASTER_ERROR == init_flag ) 
    {
        log_error( &logger, " Application Init Error. " );
        log_info( &logger, " Please, run program again... " );

        for ( ; ; );
    }

    audioamp8_default_cfg ( &audioamp8 );
    log_info( &logger, " Application Task " );
    
    audioamp8_btl_config( &audioamp8 );
    Delay_ms( 100 );
    
    pwr_mode.manual_pm = AUDIOAMP8_SET_MANUAL_PWR_MODE;
    pwr_mode.pm_man    = AUDIOAMP8_PM_MAN_3;
    pwr_mode.mthr_1to2 = AUDIOAMP8_SET_MTHR_1TO2_DEFAULT;
    pwr_mode.mthr_2to1 = AUDIOAMP8_SET_MTHR_2TO1_DEFAULT;
    pwr_mode.mthr_2to3 = AUDIOAMP8_SET_MTHR_2TO3_DEFAULT;
    pwr_mode.mthr_3to2 = AUDIOAMP8_SET_MTHR_3TO2_DEFAULT;
    audioamp8_set_config_power_mode( &audioamp8, pwr_mode );
    Delay_ms( 100 );
    
    pm_profile.pm_profile = AUDIOAMP8_PM_PROFILE_3; 
    pm_profile.pm3_man_sh = AUDIOAMP8_SCHEME_C;
    audioamp8_set_config_power_mode_profile( &audioamp8, pm_profile );
    Delay_ms( 100 );
    
    audioamp8_set_mute( &audioamp8, AUDIOAMP8_SET_DISABLE );
    log_printf( &logger, "-------------------------rn" );
    Delay_ms( 1000 );
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other mikroE Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.AudioAmp8

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

mikroSDK

This Click board™ is supported with mikroSDK – MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

For more information about mikroSDK, visit the official page.